If nothing else, the odyssey of Samsung’s 840 EVO has not been lacking in excitement. After initially launching in 2013 to great fanfare as an excellent, strong-performing low-cost drive, over the long run performance regressions began to occur in deployed drives that saw the read performance of old data significantly drop. At the heart of the issue was the drive’s relatively uncommon 19nm TLC NAND, which given the combination of small feature size and tighter requirements of TLC, eventually resulted in the drive having to slow down and re-read cells to properly read the charge-decayed cells.

Aiming to fix the issue, in 2014 Samsung released a performance restoration tool and firmware update for the 840 EVO. The combination of the tool and firmware would update the drive to better handle decayed cells and reduce the need to re-read them, meanwhile the restoration tool would refresh the drive’s data by re-writing all of the data to fresh cells. The idea being that fresh data in combination with the newer firmware would prevent the drive’s performance from decaying again.

Unfortunately that didn’t work out as planned, and while the data refresh from the performance restoration tool did bring drive performance back up, over the long run performance once again began decaying on old data, even with the firmware improvements. As a result Samsung has commissioned a second, more permanent fix for the 840 EVO. This fix involves another firmware update, this time installing a firmware that periodically refreshes old data rather than the one-off refresh of the performance restoration tool. Refreshing the data once again brings performance back up to where it should be, and the periodic, repeating nature of the refresh means that data is never allowed to get too old to let performance degrade again.

Ultimately Samsung’s second fix is a bit of a brute force solution to the problem, but at this point there doesn’t seem to be anything Samsung can do about 19nm TLC cell charge decay other than to refresh the data, as the problem is intrinsic to the NAND itself. Pre-release versions of the firmware show that this fix works, and conceptually this is much more likely to work over the long run than Samsung’s initial fix. The tradeoff is that it does consume P/E cycles to refresh the data, but by our own calculations even 5 years of refreshes at 1/week would only be 26% of the drive’s rated 1000 cycle lifetime. Meanwhile for the longer term, Samsung has since moved on to 3D-VNAND in newer drives, which is more stable than very small geometry planar NAND and essentially turns back the clock on NAND scaling issues. So the 840 EVO should be the last Samsung TLC drive to encounter this issue.

In any case, after previewing the updated firmware to the press, Samsung has released the updated firmware and its associated version of Samsung Magician (version 4.6) to the public over on their website. After an initial staggered release over the weekend – we suspect to make sure not too many users had the firmware if a problem quickly cropped up – Samsung looks to have opened downloads to everyone. However Mac and Linux users will want to note that at this time only the Magician version of the firmware has been released; the bootable ISOs for directly updating the drive have yet to be updated.

In the meantime this will continue to be an issue we keep an eye on. As with the initial problem and Samsung’s first fix, the decay issue only occurs after a time, so we’ll have to see where 840 EVO performance is in a couple months’ time. However with the very nature of the problem and the periodic refreshing of data, we’re hopeful that this will finally put an end to the performance degradation.

Source: Samsung

POST A COMMENT

74 Comments

View All Comments

  • Synomenon - Thursday, June 4, 2015 - link

    Any word on an update for the mSATA version? Mine needs it. Reply
  • Texashots - Monday, September 21, 2015 - link

    If you had magician 4.5 you never saw an update coming. After some research I found they updated to 4.7 with a new firmware update. I updated magician but could not get the now noted firmware update to work. Finally I used the ISO update and it took. Thank you Samsung for all the obviously needed help you could provide easily in your PDFs. Not! Reply
  • Industrialyzer - Thursday, October 8, 2015 - link

    @Ryan Smith I'm about to clean and reinstall everything on my macbook pro should i do the firmware update now or with the formatted /clean/ SSD ????

    i use this computer on my live performances/studio and since i installed the the 840 EVO 1TG as been giving me a lot of issues , computer running slow , OSX acting weird , this things can't happen LIVE thats why I'm cleaning everything and do a fresh install.

    Hope this update fixes the problems
    thanks
    Reply
  • jprokos - Sunday, November 15, 2015 - link

    Does the issue affect the 840 EVO blade SSD? I have a 1 TB SSD. I tried to update the firmware, but it wasn't recognized as a valid target. Wondering what to do. Reply

Log in

Don't have an account? Sign up now